67, 68, 69 dart bumper jack
67, 68, 69 dart bumper jack with base, correct lug wrench/handle for 7/16 lug nuts, bumper hook. Comes with a spare jack base. You get everything as shown in the pics. Jack works and appears in ok...
View ArticleAN Fittings
What brand AN fittings is everyone using? Why is Aeromotive at least double than other brands? The post AN Fittings appeared first on Classic Mopar Forums.
View Article22 champion radiator and champion 16 inch single fan question
Bought a 22 inch Champion radiator and the 16 inch single fan from champion as well. My problem is the radiator (CC526) fit with elongating three holes and drilling a forth finally fit. Only to...
View ArticleComplete 360 Air Cleaner to Pan $1800
I recently purchased a 67 Coronet that had a 360 with 4-speed. I swapped out for a Big Block. Nothing wrong with engine at all. I have no receipts its a 75 casting with a cast crank. KB Pistons Air Gap...
View Article72 Duster Passenger side C-pillar interior trim panel
Hey guys I'm looking for an undamaged passanger side C- pillar interior trim panel. I'm not sure if that's the right name for it so I've attached a photo. Thanks, Dave View attachment 1715056367The...
View Article73 Inner Fenders $30 OBO
Make Offer. This was cut off before the seam. Inner fenders are complete. Core support is good too. View attachment 1715056094The post 73 Inner Fenders $30 OBO appeared first on Classic Mopar Forums.
View ArticleMig Welder
Hello Everyone. Need to get started on replacing a few patch panels and knew my flux core wasn't going to cover it. I got this welder, but have no idea how to setup the gas. Can anyone help? Michael...
View ArticleWould love some advice
I am in the middle of a rest mod on my 70 Dart and am getting around to the body work. The lower drivers quarter is toast, but it seems the patch panel will cover it. I started to DA the panel and the...
View ArticleThermostat vs. No Thermostat ?
Hello All, I'm running a little more than stock 440 in my '69 Dart, she is running HOT! There is no shroud . Years back I used to by pass my thermostat run it straight in my '69 Bee 440/6/4speed with...
View Article74 Dart Vibration
In need of help. I know there is a tone of threads on here for a vibration in a 360-727 set up. I have read threw a lot of them check a bunch of stuff and am still failing to find the issue. So as for...
View ArticleNEW Duster LH & RH rear tail light bezels
These are brand new aftermarket bezels fit 73 thru 76 and are the correct finish. The only thing different from the factory ones are the mounting studs. They are heavier studs, approximately ¼ inch in...
View ArticleSpray on chrome? West coast customs
Has anyone used or seen the spray on chrome. Not the stuff at autozone. I saw it on an episode of west coast customs flipping channels didn't get the name of it. Looked pretty good but expensive. Just...
View Article68 Barracuda rear quarter window regulator slide roller – drivers side
This slide roller fits over a shaft a slides on the shaft as well the window regulator slide slot. The post 68 Barracuda rear quarter window regulator slide roller – drivers side appeared first on...
View Article18″ Wheels post pictures of your mopar on 18″ rims
Here is my 67 Dodge Dart. Might do the hemi look. View attachment 1714967675 View attachment 1714967676The post 18″ Wheels post pictures of your mopar on 18″ rims appeared first on Classic Mopar Forums.
View Article1967-71 Dart Headliner Bow sets
Have a couple of these sets on hand. Asking $60ea. plus shipping. Thanks FABO! The post 1967-71 Dart Headliner Bow sets appeared first on Classic Mopar Forums.
View ArticleTires for 15×6 wheels
I was thinking of running 15x6 cragars with a 3.375in backspace in the front of my 65 valiant, does a 195/65/15 or 205/65/15 tire fit in front of a early A with stock ride height? any pictures of these...
View Article10″ Backing Plates
8 3/4 10" backing plates, came off a 68 Dart $80 plus $18.95 shipping Mesa, AZ View attachment 1715056417The post 10″ Backing Plates appeared first on Classic Mopar Forums.
View ArticleBig Brake Kits?
Are there any big brake kits out there for stock front end A-bodies? I've come across several pages that list ones that haven't been in stock for years (Dr. Diff. and AREngineering to name a couple)....
View ArticleReturn style pressure regulator.
I'm collecting parts for the fuel system for my Magnum EFI project. I will build a return style system with the regulator at the firewall. I've used Aeromotive products in the past, but was wondering...
View ArticleAnd so it begins….
40+ acre brush fire not to far from us...lot of aircraft buzzing the lake for water... The post And so it begins…. appeared first on Classic Mopar Forums.
View Article