Car club questions?
Hey all, wanted to pick your collective brains on car clubs. Never been in a car club and frankly not remotely knowledgeable on how they work. Those who are in them, are you in Mopar exclusive club or...
View ArticleA833 TRANSMISSION 70 A BODY
I have a 70 a body 833 short shaft transmission for sale, asking $475 plus shipping. This transmission is in excellent condition was told it had been gone thru so pulled side cover off to have a look...
View ArticleDark gray color for center cap ralley wheels
Anyone know the color i can get in a rattle can at local store that matches the closest to the dark gray color for the cone ralley caps? The post Dark gray color for center cap ralley wheels appeared...
View ArticleScottsdale Pavilions Car Show gets a Mustang-leaving-a-car-show wreck
Video of it happening here: http://jalopnik.com/maybe-there-s-not-safety-in-numbers-1794995853 Aerial footage that shows it's at Pavilions here: The post Scottsdale Pavilions Car Show gets a...
View ArticleAlignment Question
Yesterday I had a New Pitman Arm, Center Line, and Idler Arm replace due to a problem with slop in the pitman arm and center line. The place I took to have the work done was a good place for front end...
View ArticleWhat caused this?
I know this isn't a Mopar, but I don't want to make the same mistake when I paint my Mopars. Two years ago I painted my wife's Murano. It was the typical primer/sealer then base/clear. Everything...
View ArticleFactory Type S front brakes sway bar and cross member
How hard are the factory Type "S" k frame/brake/sway bar setups to find. Also what would used setup sell for that has set up for years.The post Factory Type S front brakes sway bar and cross member...
View Article1969 Valiant 4 door
So a few years ago, I got a wild hair up my ass and got this car off craigslist. Paid like 2k for it and it was in great condition for being a Nebraska car. It had a 273, 904 and 7.25 in it. So just a...
View ArticleDistributor point screws.
Ok, what size are the screws that hold the points down? None of the so called parts guys seem to even know what im talking about. The post Distributor point screws. appeared first on Classic Mopar...
View ArticleCORRECT CARPET
1972 Demon 340, 4 speed with front bench, no console, built October 27, 1971. What is the correct carpet I need? 80/20 Loop or Cut Pile? Thanks!The post CORRECT CARPET appeared first on Classic Mopar...
View Article15″ Steering Wheel – Vs. – 13″ Steering Wheel ?
With a manual steering box, in a 65 Valiant, or similar, tight turning with a 13" steering wheel is difficult. -- Has anyone switched from a 13" wheel to a 15" wheel, and if so, what has been you...
View Article1970 340 engine
1970 340 "OR" engine. Block, main caps, crank, rods, pistons, new cam bearings, new frost plugs. Crank is standard. Pistons are p3690825 .030". $1000. Pick up only. Located in Toronto Ontario Canada...
View ArticleIdentify Hurst Shifter
Does anyone recognize what shifter model this is? I don't recognize the mounting plate but was told it was for a Mopar ... sure doesn't look like the one on my A833 O/D from my Duster (the rods are way...
View ArticleMaster cylinder brake pedal rod
I have for sale a master cylinder brake rod that came from a 71 Duster. It’s been cleaned and has an overall length of 6 ½”. I could not see any damage of any kind on it. I would like to get $15 plus...
View Article904 transmission yoke, small U-joint
I have for sale a nice 904 small U-joint trans yoke. It doesn’t look to be damaged anywhere and the U-joint ears look great. I would like to get $20 plus shipping for the yoke. Ken Edison, NJ View...
View ArticleEarly style biscuit type trans cross-member
I have for sale a nice early biscuit style trans cross-member. It’s just needs to be cleaned and painted and comes with the trans mount. I would like to get $25 plus the shipping for the cross-member...
View ArticleEarly style biscuit typle trans cross-member with attaching nuts and bolts
I have for sale a nice early biscuit style trans cross-member. It’s been cleaned and painted and comes with the cross-member attaching nuts and bolts. I don’t have the trans mount though. I would like...
View Article904 trans dust shield, small block LA engines
I have a decent 904 transmission dust shield for any of the small block LA engine applications. It has some small dents but is still in decent shape. I would like to get $15 plus the shipping for it....
View ArticleB/RB 727 trans dust shield
I have a decent 727 transmission dust shield for any of the B/RB engine applications. It has a small dent but is still in excellent shape. I would like to get $15 plus the shipping for it. Ken Edison,...
View Articlemy car is live! I mean 12v live!
So my son and I are coming near to starting up his 70 Duster that has been sitting in a barn for years and now that the mechanical is done we put in a fresh battery to see what works and doesn't, we...
View Article