65 A, B, C Body, Truck and A100 Series Shifter Knob
Found another 65 A, B, C, Truck and A100 series floor shift knob. It's in decent shape for being 50 plus years old. Still has the set screw to secure it to the Shifter. $20 shipped from 22657 View...
View ArticleKelsey Hayes Disc Brake Wheel Lugs/SBP Mag Wheel Lug Nuts
i found a LH and RH thread Kelsey Hayes disc brake SBP wheel lug and 5 Mag wheel SBP RH thread nuts. Cleaned up the the nuts would be suitable for a driver. $20 for all shipped from 22657 View...
View ArticlePower Trunk Latch
Here's a later model (probably M or J Body) single power wire trunk latch. What you see is what you get - I do not have the momentary switches or any other wiring. These type latches bolt right in...
View ArticleSteering Shaft Nut
I seem to have misplaced my steering shaft nut in the 24hrs that it's been off the car. Can I use a generic nut for this? Anyone know the thread? Power steering auto column for a '69 Val if that...
View ArticleHello Clint1 in western Louisana!!!
Does anyone know if the member here called Clint1 is still active on the site or around? He was parting a 1966 Valiant last year and there's some parts (rear window, deck lid and doors) that I'm pretty...
View Article7.25 Complete Rear End
7.25" open, 2.76 gears, 5x4.5 bolt pattern complete rear end from my '73 Dart. Includes complete 10" brake system (less brake lines), shock plates, and fairly new u-bolts. No leaks, gears look good,...
View ArticleTrunk lids
Does anybody know if a 65 Valiant trunk lid will fit on a 66 with little or no modifications? Also, are the back windows interchangeable? The post Trunk lids appeared first on Classic Mopar Forums.
View Articlelooking for A body linkage lever for reverse
Looking for lever that stamp "R"The post looking for A body linkage lever for reverse appeared first on Classic Mopar Forums.
View Article1968 340 motor with edelbrock aluminum heads and intake
1968 Chrysler 340. complete motor less carb and distributor. Ran great when I took it out of the car. I replaced it with a date correct motor. The block date code is 6-22-1967. I am asking $2200 or...
View ArticleAnyone used a McLeod RST Twin Disc dual clutch set up?
I was looking at a few clutch set ups for my 4 speed 416 stroker and came across this McLeod unit. There is not much feedback on Summit or other resale sites. Would appreciate any feedback from an...
View ArticleHF leakdown test is a Piece of Big Steenkeeng SHTUFF but here is
..........how I hope to fix it Bought one of these awhile back thought "how bad can it be.?" Paid what, 40 bucks? Cylinder Leak-Down Tester View attachment 1715050286 Looks GREAT, right? HERE IS the...
View ArticleWanted ! A Body seat rails.
Hi, we need a complete set of seat rails or, even 1 side to fit a 67 bucket seat A body. Thanks, D.y The post Wanted ! A Body seat rails. appeared first on Classic Mopar Forums.
View ArticleQuickTime T-56 Starter Issues
I'm wrapping up a T56 magnum swap using the QuickTime bellhousing for an LA. Went to fire it up today after many months of work and 'crunch '. The starter is grinding the flywheel bad, it sounds like...
View ArticleEFI Fuel Pumps
Thinking about an EFI setup. And as we all know the fuel system is the key. SO my questions are: In tank VS in line. Best brands/setups. Return or no return. Im thinking Aeromotive Phantom 200 and MSD...
View ArticleA body 340/360 engine mounting brackets
i probably have 10 sets of E body brackets but I can't seem to dig up a set of A body ones out of my garage. Anybody have a set they will part with? The post A body 340/360 engine mounting brackets...
View ArticleHood pin replacement
Not an A-Body, but the concept works on any car. Tired of looking at cheap hood pins on my 68 Satellite, so ordered a pair of 2.5" Epman Quick Latches to replace. Had to grind a little fiberglass...
View Articlesbp 14’s
looking for a set of 4 ; small bolt pattern 14 inch wheels . Anyone in the souther California area . Looking for pick up preferably not sure how much shipping would be to CA 91731 The post sbp 14’s...
View ArticleM Code K frame question…
my m-code cuda is now sitting in my garage after a year and a half with AMD's resto shop "rebuilding" the car. i'm starting to think about parts i will need. the k frame in the car was "butchered" by...
View Articleduster side window moldings
I have a 1970 340 duster that has chrome moldings at the outside, bottom of the side windows. Approximately 1/2" x 1/2". The door & body has holes for attaching clips that are close to a 1/4". I...
View ArticleMy 68 dart coming together!
Finally got all 4 back on ground! Everything on suspension new front to back and added hellwig front sway bar! View attachment 1715050430 View attachment 1715050431 View attachment 1715050432 View...
View Article