Sway Bar Length?
Question? What is the length between the mounting holes on a 68 to 72 A body sway bar? There must be a general measurement. Factory location. Not aftermarket. Any info or past posting would help....
View ArticlePrice on Mid 80’s D350 Ram Help
Dont know much about pickup trucks and have never owned one. Have seen one for sale I like. What would you expect to pay for mid 80's D350 Ram V8 rear dual wheel pickup in reasonable condition?. Not...
View Articlewheel to fender clearance
how much clearance is needed for the wheel to fender. i got a half inch of clearance between the tire and the front lower corner of the rear fender.. The post wheel to fender clearance appeared first...
View ArticleThermoquad idle issue
Trying to smooth out my idle, only to find that if I begin to close the primary butterfly slightly the idle begins to run better. I have all new vacuum lines and thick carb gasket. A vacuum leak cannot...
View ArticleWhat are my spark plugs saying?
Hey Fabo, I have 1500 miles on these plugs. They are from cylinders 1 & 2 of my 340. For the record I have an MSD and a Holley SA 670 What do you think? View attachment 1715051629 View attachment...
View Article225 Slant needs a good idle. what rpms are you spinning?
I think I asked this once before, but I want to be as specific as possible here. 66 dart, slant, sedan, super six conversion , carter bbd, HEI conversion, 904 auto. ok, so after engine is completely...
View Article440 Intake STR 6 Pack and Single 4 Barrel Dominator
This is a mint condition STR -14 It comes with a 6 pack top and it also comes with a single 4 barrel Dominator top. Was only mounted on a motor 1 time but never ran. $1500.00 for everything plus...
View ArticleStalling
well I finally gave the 383 4 gear a test drive, my driveway has a slight incline on the way out, as I was backing out the car was stalling, I had to rev it up a little and let the clutch out a little...
View Article1970-1976 am fm radios
i have two Dart am fm radios $400 each Not tested View attachment 1715051450The post 1970-1976 am fm radios appeared first on Classic Mopar Forums.
View ArticleLooking for A body Hemi headers
anybody have a set of A body Hemi headers they want to sell? The post Looking for A body Hemi headers appeared first on Classic Mopar Forums.
View ArticlePopping fuse when stepping on brakes
Weird electrical problem happened today while taking my 68' Dart around. First noticed my factory amp gauge pegging the 'D' side in rhythm with the turn signal on in left position. Flasher clicking but...
View ArticleWhat you wish you had kept
I'm selling off my parts car to a friend. All that's left is the body. Which peices of metal do you wish you had kept? I'm afraid I'm selling something I may need in the future. Thoughts?...The post...
View ArticlePie cut my brake pedal and new door panels.
My pops drove the dart the other day and complained about how far the brake pedal was out front of the gas pedal. He was biching up and down how it's not safe and if I ever need to do a emergency stop...
View Article1971 Demon RE-DO not Restore 6X2
I really don't have the time or money to start another car but I just couldn't wait! I bought this Demon from a member here (billstickly1) and it was in really good shape....not much rust at all. The...
View ArticleG54B 2.6L Complete 4 Cylinder Head
For sale is a New in open original box. G54B 2.6L Complete 4 Cylinder Head. Fits 1983-89 Chrysler, Mitsubishi. ( may fit others ) Please do your research to be sure it fits your needs. I inclosed pics...
View Articlevin number location
Recently bought a 65 dart conv. off web had it shipped to me after looking it over I found no rivets in tag just a spot of glue under tag. Is vin numbers any where else on the body? The post vin number...
View Article1967 Plymouth Barracuda 340 4-spd
1967 Plymouth Barracuda 340 4-spd posi 3:91, aluminum intake edelbrock 700 CFM Power steering front disc brake. Fresh new flow master exhaust Mopar exhaust tips. Older restoration but very well...
View Article2-727s rebuilding 1, question
I have never rebuilt a automatic transmission yet, but I have a 1979 727 with a lock up and a 68 727 both for small blocks. The kit I have is B&M part no 10229 for non lock up. The one I will be...
View ArticleMopar Electronic Vacuum Advance Unit 1970-1 383 440 Cubic Inch HP Engines
Mopar Vacuum Advance Unit 1970-1 383 440 Cubic Inch HP Engines PN 3438262, possibly NOS does not look like it was ever mounted. Asking $100 and the ride also open to offers. View attachment 1715051494...
View Article2017 Mopar HIPO car show
May 13th, 2017 Omaha, NE We host the largest Mopar show in the area. If you are in the area we would love to see you there. View attachment 1715014365The post 2017 Mopar HIPO car show appeared first on...
View Article