Blocked coolant passages from head gasket installation?
I got a call this evening from someone who has a friend that may have missed a step. He just replaced the heads on his 360 in a truck and it's running hot. Heads were good to go and everything...
View ArticleModified LD-340
Up for sale is my old LD-340. Purchased from a speed shop over 20 years ago as seen here. Center divder milled down as per the old DC spec. Other work as seen below shows welding of the side to build a...
View ArticleDirect connection small block valve covers
Looking for set of used direct connection small block valve covers.thanks The post Direct connection small block valve covers appeared first on Classic Mopar Forums.
View Articlestock 340/360 exhaust manifolds
Looking for a pair of stock 340/360 exhaust manifolds not the hi dollar rare hipo manifolds! I'm putting a 360 in my 65 dodge dart. Willing to buy but not pay for over priced eBay part prices! Can...
View ArticleSteering Wheel
For sale is a Steering Wheel off a 1970 Plymouth Duster. It's in very nice condition. No cracks or splits. Also includes the original horn center. $50.00 plus shipping. or I can deliver to the All...
View ArticleCompatible parts with 1970 dart
hey I'm new to this site just signed up. Probably going to be pretty active since I don't know much about dodge. I picked up a 1970 Dodge Dart swinger that is missing quite a few parts. Was curious can...
View ArticleAnyone know what this bracket is?
This bracket was in a box of engine parts that came with a late 70's early 80's 318 that I bought. Anyone know what its for? View attachment 1715053047 View attachment 1715053050 The post Anyone know...
View ArticleCam for torque question
Hi All, I've got a 318 built to zero deck with forged 1.8 compression height pistons .040 over. Indy RHS heads @62cc's with about 9.5:1 compression. Eddy air gap intake and holly 650 carb. It has a...
View Articlemopar truck/car parts for sale
I have a few odds and ends for sale . I have a pair of 1995 dodge truck magnum exhaust manifolds for sale. 40.00 obo. I also have a pair of 70's/80's truck 360 exhaust manifolds for sale. 40.00 obo . I...
View ArticleAfter a new windshield…
I now would like to cover the rubber windshield gasket with trim. What was there a rounded T shaped trim with an extrusion to hold it. View attachment 1715034854 I'd like to know if anyone has found a...
View Articlewanted 318 truck exhaust manifolds
Want a pair of 70's -80's non emissions 318 truck exhaust manifolds. Must fit 318! Do not want 360 manifolds ! Too big of ports causes exhaust leaks!The post wanted 318 truck exhaust manifolds appeared...
View Articleanyone know about 87 broncos?
im planning to go look at one tomorrow i mostly want it as a plow vehicle anything in particular i should look for, or avoid? any known problem areas (other then being a ford) ? The post anyone know...
View Article1972 Dart Rear Light Assembly
Want to purchase a 1972 Dart Rear Light Assembly, don't need lens, just need Driver side but will purchase both if that is required. Need to be in good condition. The post 1972 Dart Rear Light Assembly...
View ArticleFNG with ’71 Dart
View attachment 1715053055 View attachment 1715053056 Hello all, I just picked up my new project. A 1971 Dart, automatic with a 318. I am going to keep it stock, for now...but I am no stranger to...
View Articlequestion about a dodge ram
I have a chance to purchase a 96 dodge ram at a good price. I miss having a truck. I went to drive the truck today and although it has high mileage, it ran really well. When I went to park the truck...
View ArticleAnyone repair stock antenna cable?
The connector for the back of the radio pulled off the antenna cable. I cut the cable back a little hoping to find the "coax but there is just a plastic shield inside with 1 tiny strand of wire running...
View ArticleB3 Racing Engines Geometry Kit
Recently I added Eddy heads, Air-gap RPM intake, Hughes roller cam and roller lifters to my "LA" 360 engine. The Comp Cam roller rockers that was on the engine are 1.5 ratio and decided to reuse them....
View ArticleLA360 initial timing too high – are there different timing covers?
Hello all. I've lurked around here for a while (lots of great info that helped me on my 73 Scamp project - thanks), but I've not been able to find info on my current issue... Timing way to high....
View ArticleNintendo SWITCH + Zelda + accessories!
Hey guys, I know this isn't the place you would typically go to find something like this but I figured it was worth the try. My son HAD to have these and he actually saved up his own money to purchase...
View ArticleLeak between motor and trans at a mounting bolt
Anyone ever have a leak at a tranny bolt near the oil filter? I just dropped the engine and then mated it to the transmission. My guess: I might have torqued the left side down too tight before getting...
View Article